My wife and I love our front-loading Whirlpool Duet washer/dryer.It has many features but we really appreciate the sanitary wash cycle that is absolutely necessary if you have young children around the house.
Unfortunately, we started noticing that our washer was taking longer and longer to run as the time went on.
For example, tt should only take about 45 minutes to run a normal cycle but it was taking over 1.5 hours! To boot, the clothes didn’t quite smell clean either.
Prolonged wash cycle time for 2+ year old Whirlpool washing machine ( model # GHW9400SU0 )
Simple internet search pointed to a clogged drain pump cap as the possible culprit. Whirlpool wanted to send a technician out for $175 so I decided to take it apart myself to find out what was going on inside.
Most Whirlpool Duet washers (GHW9400)
Required Tools and Materials
- Owner’s Manual – don’t have one? Download a Whirlpool Duet Washers GHW9400 manual here (external link to Whirlpool)
- Socket, Ratchet, Socket extender
- Torx Bits – if you don’t own a set, I highly recommend the Anytime Tools 100+1 Piece Tamper Proof/security Screwdriver Bits and 1/4″ Reversible Ratchet Screwdriver Handle. I purchased Neiko 100-Piece Security Bits Set with Hard Storage Case because I already owned a ratchet screwdriver but it ended up breaking about a week after I got the bits. Lesson learned? You can’t have too many ratchet screwdrivers!!
- Ratchet Screwdriver – Any will do but I recommend a very sturdy with thick shaft – Klein Tools 32500 11-in-1 Screwdriver/Nut Driver with Cushion Grip) and
- Lots of towels
- Adjustable pliers (it looks like this ChannelLock)
- One, large plastic bag
I used to not be able to walk pass a bargain tool bin. But over the years, what I learned is that it is a royal pain to have one of your tools fail in a critical point during a DIY project (i.e. plastic screwdriver handle that spins independent of the shaft rotation). So whatever you do, please save some time, headache and money by avoiding those $5 bargain tools. I used to buy Craftsman tools exclusively but I also buy Milwaukee, Kobalt (Lowe’s brand) and Husky (Home Depot’s brand) as well.
- Using a torx ratchet or screwdriver, carefully remove the bottom two nuts from the access panel;
- There is a service manual taped on the bottom; carefully remove it and set it aside; if you don’t see one, you can download a copy by (clicking here)
- Open up the plastic bag and position it under the drain cap (drain pump assembly will have approximately a cup of residual water inside);
- Place few towels inside and outside the plastic bag;
- Using the adjustable pliers, twist the drain cap counter-clockwise; this tool is needed to initially “break” the seal; the drain cap can be removed by hand afterwards
- Clean off all the debris;
- Use some Clorox wipes to get the gunk off;
- Clean around the drain cap and threads to ensure that they will mate properly without leaking;
- Re-install the drain cap, using adjustable pliers to tighten the final quarter turn (do not over tighten)
- Remove the wet towels and plastic bag and dry off the area;
- Lay down 3 or 4 sheets of paper towels underneath the cap assembly;
- Run a normal cycle and observe the papertowel to see if there is any leak (if there is a leak, repeat from Stepa #8-11);
- Reinstall the access panel.
I ran a normal cycle to wash out any small debris and was satisfied to see that my cycle time went back down to 45 minutes.
There is no way to avoid this from happening (well, I guess I can empty out my pockets before dumping the clothes into the washer 🙂 ) so I just need to check on this cap every month or so as a preventative step.
Please let me know if something is unclear and I will try my best to answer your questions.
Good luck and thanks for reading!
By the way, if you found this article to be helpful, would you please do me a favor and sign up of my free my newsletter? The signup form is located on the upper right corner of the page.